Each person may have their unique piece of advice when it comes to How to Install a Bathtub.
Mounting a bathtub isn't exactly brain surgery, however it does require solid plumbing, carpentry, and occasionally, tiling skills. Replacing an old bathtub with a new one is also a reasonably hard job. If the old bathtub is readily obtainable, the job can move quickly; if you have to open a wall surface to get rid of the old tub and also position the brand-new bathtub, the task is a lot harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub and set in the new one. Make certain you have actually qualified yourself for the task and fit attempting it. As opposed to working with a specialist to take control of a halfway-completed project, it is far better to take into consideration utilizing one before you begin. Opportunities are you might require a specialist plumber to make tube links.
This post will certainly aid you mount a brand-new tub in your washroom if you have actually currently acquired a new bathtub and also do not need to change the setup of your previous water supply pipelines.
Your tools and product list ought to comprise the following:
Planning for the Installation
To start with, the sustaining frame supplied with the bathroom needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its final position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is separate the water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of getting rid of the existing taps can be quite problematic as a result of the limited gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipes. When the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, put the bath tub in the called for position. The wooden boards are valuable in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bathtub till the spirit level checks out level.
To set up taps, fit all-time low of the furthest adaptable tap connector to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the supply of water and also examine all joints and also brand-new pipework for leaks and tighten them if needed. Fill the bath tub and additionally inspect the overflow electrical outlet and also the normal electrical outlet for leaks.
Lastly, take care of the bath paneling as defined in the supplier's instruction manual. Tiling and also securing around the tub needs to wait till the tub has been made use of at least once as this will certainly settle it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, then you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washers are in location in between the tap and also the sink. Secure the faucet in place with the producer offered backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former kind ought to be attached to the tap finishes initially, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface in between the bath and the tiling, resulting in issues with dampness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bathtub with water before securing, to allow for the activity experienced when the bathtub remains in use. The sealer can break relatively very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily available on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an associate on our other website. So long as you appreciated our article if you please do not forget to pass it around. We appreciate reading our article about Tools You Need to Install a New Bathtub .
Schedule A Free Estimate